Is it OK to use a wood stove chimney for a pellet-burning stove? Yes, it is! Pellet stoves can use an exhaust pipe that’s vented through a side wall. Unlike a traditional wood stove, pellet stoves are easy to install either way and can be adapted to existing chimneys.
Pellet stoves can be used with an existing wood stove chimney, but is this the best way to vent these stoves? This article explains your options. It also provides information on how to use a wood stove chimney for a pellet stove.
Many pellet stoves are even approved for mobile homes. Pellet fuel is typically purchased in 40-pound bags. One bag will provide up to 24 hours of continuous heat, so you can get through a winter on a hundred or more bags.
Pellet Stove Venting Guidelines
A wood heating stove either uses firewood or wood pellets. A pellet stove uses wood pellets, which are special fuel composites that require a particular venting system.
The pellet stove’s temperature is cooler, making it more likely to develop creosote. Because of this, pellet stoves require proper ventilation. If not, a fire can start in your chimney. To some extent, his problem is common for both types of stoves.
Pellet stove venting requirements
If you’re considering installing a pellet stove in your home, you need to know about the pellet stove venting requirements.
You’ll need a source of fresh air to feed your stove, as well as a place for waste air to escape. Some pellet stoves have an intake air vent and a flue socket on the back. While most do not require a direct vent for fresh air, all stives need a place to exit exhaust air and dispose of it outside.
A good way to determine your exact venting requirements is to read the manufacturer’s data plate. It will tell you how far the stove’s exhaust pipe should be from combustibles, as well as the specifications for adequate venting.
For example, the stove’s vent pipe must also be at least 3 feet away from any gas meter or air intake for forced air appliances. Pellet stoves are made for both freestanding and fireplace insert installations.
Pellet stove venting options
Pellet stoves need a minimum clearance from combustible materials to operate safely. It’s always a good idea to allow more than the minimum clearance for installation and service.
A pellet stove also requires electrical power for the fan and pellet feed, so you should place it near an outlet with the proper voltage and grounding.
Check the polarity and circuit breaker for a pellet stove before purchasing. As a general rule, Pellet stoves should be vented at least four feet above ground.
What is the best way to vent a pellet stove?
The simplest method of pellet stove exhaust removal is horizontal venting. To do this, simply attach a vent pipe to an adapter located at the back of the stove.
Run the vent pipe outlet at least six inches from the exterior wall surface, and install a wall protector plate to prevent possible discoloration from the stove exhaust.
If you are not satisfied with the standard chimney or roof venting in your home, there are other options available. Pellet stoves can be vented directly through an exterior wall, or directed into an existing a masonry or metal chimney.
For brick chimneys, you must install a lined flue. If the diameter of a steel flue pipe is more than six inches, you must install another chimney liner.
For other venting options, you can use a roof or ceiling vent. To use a vent in a crawlspace, you must have a ventilated crawlspace or basement.
Can you convert pellet stove to wood stove?
While you may have heard of converting a wood stove, you may not be as familiar with pellet stoves. The two types of stoves use different fuels and the main difference is the size of the firebox.
A wood stove has a large firebox lined with fire brick, and a thicker cast plate is used for the burn area. Pellet stoves feed pellets into the main burn area and have more burn control as a result
Another difference between a wood and pellet stove is their longevity. A pellet stove may last about ten years if properly maintained.
Pellets are slightly more expensive per ton, but they last longer and the stoves require less maintenance. A well-built pellet stove can last ten years, while a poorly maintained stove will only last you a few years.
This means that it’s best to choose a high-quality stove with a ten-year warranty, rather than a cheap one that only lasts a couple of years.
Pellet stove installation requirements
To properly vent a pellet stove, you should follow the manufacturer’s instructions for installation. You can find this information on the data plate on the rear or side of the stove. The exhaust pipe should go out an exterior wall, up a chimney, or through a roof.
Make sure to follow all regulations to ensure that the vent is sealed properly and that you do not breathe in the flu gases.
Depending on the size of your pellet stove, an existing masonry chimney can be used to properly vent your pellet stove. If you do not have a chimney, you can install a venting system in your home that requires a permanent connection to the outdoors.
Can you use a regular chimney for a pellet stove?
Many people think that they need a chimney for a pellet stove, but this is isn’t true. There are other ways to vent a pellet stove, but you can use and existing chimney if available.
It is a good idea to consult a dealer before making any decisions about venting.
A regular chimney may not suited for pellet stoves, and a professional survey will be needed to ensure that the ash is not deposited on the roof of your home. A proper pellet stove installation will also ensure that creosote does not build up in your chimney.
All stoves represent a fire hazard, and you should avoid putting your stove anywhere near anything that could catch fire. In addition to proper ventilation, you should always remember to keep the area around your stove clear of any combustible materials.
Pellet stove use the same chimney as a wood stove?
A pellet stove doesn’t require a chimney to burn fuel, but it does require a way to vent the exhaust outside. You can install a through-wall fitting to keep the stove vent pipe away from combustibles, or you can connect a stainless steel chimney liner to your existing fireplace. If you don’t want to install a chimney liner, a pellet stove can be vented directly through a wall.
Most wood and pellet stoves can be installed in an existing fireplace. Free-standing fireplaces may have stovepipes that are installed above or below the damper.
What kind of chimney do I need for a pellet stove?
The stove is then inserted into the fireplace opening. While most pellet stoves can use the same chimney as a wood stove, some models require an external air supply. This air supply system does not have to be installed directly into the stove, but must be located near it.
A wood-burning stove requires firewood that is seasoned and ready for burning. A pellet stove, on the other hand, uses recycled wood waste pellets.
Because both wood and pellet stoves burn wood for fuel, both are slightly greener than fossil fuels. In addition, a wood-burning stove requires little electricity and is built with fewer parts. Pellet stoves may require more repair work in the long run, however, whereas a wood burner can last up to 25 years.
What is the best way to vent a pellet stove?
When installing a pellet stove, there are a few things you should know. For one thing, you need to have a venting system in place.
While it is possible to route the vents to the outside, most people prefer a drafting effect. That way, the smoke and gasses will escape through a natural process. You should always make sure that the vents are at the proper height and speed.
You may also want to consider installing a chimney or other method of fresh air venting. A professional will usually vent a wall-mounted or freestanding pellet stove through the ceiling. This will ensure that any bad air does not make its way into the house.
Does a pellet stove need a fresh air vent?
Also, make sure there are no combustible materials in close proximity to the outside vent. If you plan to use your pellet stove as a whole-home heater, you should consider a central location. Make sure you have an outlet nearby and a wall that will allow you to run the vent.
Once you have a vented chimney, you should consider installing an L-vent pipe. This type of pipe requires cutting a hole in the side of a building to access the back vent.
It is crucial that the pipe has at least a 3 to 4-foot vertical rise because if there is a power outage, smoke will rise naturally. If your pellet stove does not have a vented chimney, then you should consider installing a L-vent pipe.